The last article shared the unpacking of the newly launched COOLERMASTER MasterCoolLibrary MasterLiquid120. The last question about the dual fans, a 4pin and a 3pin, was answered by a valued friend. 3pin removed a speed measurement line and did not affect it. The speed control function, this article mainly carries on the brief test to this integrated water-cooled installation and the performance, mainly is stronger than my original air-cooled on the line ah~
One-piece water-cooled upstarts: COOLERMASTER Cooler Master Master Liquid 200 Radiator Radiator Unpacking Once, the author is a PC-DIY enthusiast, and also met many friends through DIY. With the passage of time, I have become a bricklayer laborer. The former friends have also developed in all walks of life. They do not remember when their own procrastination was so severe. It took nearly 2 months to use this integrated water-cooling to give up the open box. Want to ask the effect? Of course, there are follow-up articles in the neighborhood there is a neighbor PC installed a full water-cooled, playing lights to really cool, and I Sakura dance butterfly fly | Like 3 Comments 18 Collection 13View Details Part 1. Installation is simple and effortless Installed CPU heat sinks have their own feelings, the heat sink is strictly pressed on the surface of the CPU, trying to tighten the screws requires a lot of effort, and this water-cooled installation is much simpler. Just install it for the first time or follow the instructions in the manual.
The original air-cooled ID-COOLING 6 heat pipe is also available, with its own thin blade fan.
But before using the silicone grease to tell the truth is not very good, more than a year can see that the surface of the grease is not covered and the edge has been liquid, taking advantage of this chance to replace the cool mother comes with good thermal grease it.
The surface is wiped clean and leaks out of the CPU body. Once the E3 was a generation of God U, the performance would be very serious. Actually, there is no nuclear display and it is very embarrassing. For example, I would like to quickly and without playing games also need a matching machine card.
Cooler Master MasterLiquid 120 CPU Cooling Radiator (Multi-Platform/Dual-Cavity Water Pump/Slim Water Copper/Low Noise) 499 RMB Jingdong Direct Link 
After the debut of the protagonist, the fan is installed, the fan is mainly to ensure good wind direction is better to avoid the hot air blowing inside the chassis, although I sent two fans I installed a, because the two are installed is a bit fat.
Thermal backplane This design is relatively novel. The foot screw is fixed by this snap-fitting to avoid misalignment. It is easier to screw than a traditional screw and does not require a screwdriver. However, if this snap-in type is broken, it will be awkward.
Complete the drawing so that the backplane can be plugged into the motherboard's four thermal holes.
The pump has grooves and fool-proof protrusions in one turn. This metal frame can be put in and fixed with screws.
Complete the diagram so that most of the work is done.
Backplane insertion, here we must pay attention, Intel's board LOGO exposed.
Apply high-grade silicone grease to the CPU. The silver grease should be a silver-containing bar. At least it will not be a 5-dollar waste.
Then, the four cooling screws of the water-cooling pump and the back plate are fixed. As with normal heat dissipation, the diagonal screws are tightened first, or the other side will be warped and installed.
In fact, the small partner here will see it, and the embarrassing thing happened. The Joe Sibo UMX1 PLUS chassis has no place to put the cold row. . . Well dragging the long tail, did not think of such a problem before. Of course, there are solutions, and the top fan of the chassis is replaced but four holes need to be drilled from the top. There is no tool at hand, dragging the outside effect should be better some haha.
To a handsome LOGO show, although not as good as the Pro series transparent top cover cool, but this year has a lamp is high-end performance, isn't it?
The strength of Part 2.Cool & QuietI always felt that Cool & Quiet's phrase was familiar, and then I remembered that AMD had a special CNQ's BIOS design vernacular called "cold and static." Still, it was very appropriate.
In addition to the traditional 4pin speed-adjustment function, in fact the cool god of the ice god G fan can stop, stop you know, it is 0 dB ah. Many people, including me, have installed fanless to achieve extreme silence. I used to use the Lehman HR02-M without fans to press on the AMD X220, and I chose this water-cooling system without any problems.
First look at the temperature of the previous air-cooled test and the temperature of the standby AIDA full-load test.
Northeast warm, indoor temperature 24 ~ 25 °C, air-cooled standby temperature is 60 °C, full load reached 86 °C.
Ice God G MasterLiquid120 pressure E3, standby temperature 44 °C, full load is 58 °C.
And through the time we can also see the authenticity of the temperature test, 11 o'clock noon test is the air-cooled, 17 o'clock at night test is the water-cooled temperature.
The cool mother's technical strength is clear, and before I used an integrated water-cooled cooling fan, the noise of the fan made me give up the integrated water cooling, so this experience gave me a new understanding, mainly in daily standby. The fan is basically in a stopped state. Even if the fan is noisy at full load, it gives me a quieter working environment.
Only, I may need to change a chassis to fit it. The life of DIYer is tossing. . .
Wuxi Doton Power , https://www.dotonpower.com